- 您现在的位置：买卖IC网 > Sheet目录527 > SX1211SKA915 (Semtech)KIT STARTER FOR SX1211 915MHZ
SX1211
WIRELESS & SENSING
5.4. Buffered Mode
5.4.1. General Description
As illustrated in Figure 38, for Buffered mode operation the NRZ data to (from) the (de)modulator is not directly
accessed by the uC but stored in the FIFO and accessed via the SPI Data interface. This frees the uC for other
tasks between processing data from the SX1211, furthermore it simplifies software development and reduces uC
performance requirements (speed, reactivity). Note that in this mode the packet handler stays inactive.
An important feature is also the ability to empty the FIFO in Stby mode, ensuring low power consumption and
adding greater software flexibility.
SX1211
CONTROL
IRQ_0
IRQ_1
Data
Rx
SYNC
RECOG.
SPI
CONFIG
NSS_CONFIG
FIFO
(+SR)
Tx
DATA
NSS_DATA
SCK
MOSI
MISO
Datapath
Figure 38: Buffered Mode Conceptual View
Note that Bit Synchronizer is automatically enabled in Buffered mode. The Sync word recognition must be enabled
(RXParam_Sync_on=1) independently of the FIFO filling method selected (IRQParam_Fifo_fill_method).
5.4.2. Tx Processing
After entering Tx in Buffered mode, the chip expects the uC to write into the FIFO, via the SPI Data interface, all the
data bytes to be transmitted (preamble, Sync word, payload...).
Actual transmission of first byte will start either when the FIFO is not empty (i.e. first byte written by the uC) or when
the FIFO is full depending on bit IRQParam_Tx_start_irq_0.
In Buffered mode the packet length is not limited, i.e. as long as there are bytes inside the FIFO they are sent.
When the last byte is transferred to the SR, /Fifoempty IRQ source is asserted to warn the uC, at that time FIFO
can still be filled with additional bytes if needed.
When the last bit of the last byte has left the SR (i.e. 8 bit periods later), the Tx_done interrupt source is asserted
and the user can exit Tx mode after waiting at least 1 bit period from the last bit processed by modulator.
Rev 8 – February 2013
Page 44 of 92
www.semtech.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SX1223SK868
KIT STARTER FOR XE1223 868MHZ
SX1231-31SKB915
TVS
SX1240SKA433
TVS
SX1701BI085TRT
IC AMP 2.5GHZ 5.3V 16-MLPQ
TA002-10002
LED HEATSINK W/FAN 12V 40X10MM
TC620HEPA
IC TEMP SNSR 5V DUAL TRIP 8-DIP
TC623CVOA713
IC TEMP SNSR 3V DUAL TRIP 8-SOIC
TC624VOA
IC TEMP SNSR PROG 2.7V 8SOIC
相关代理商/技术参数
SX1212
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra-Low Power Integrated 300-510MHz Transceiver
SX1212-11SKA433
制造商:Semtech Corporation 功能描述:SX1212 433Mhz USB Kit With 2 SX1212-01SKA433SMA, Antenna Connector, RS232 Cable
SX1212-12SKA433
制造商:Semtech Corporation 功能描述:2 X SX1212SKA 制造商:Semtech Corporation 功能描述:Deluxe USB Starter Kit for SX1212, Includes Two USB Interface Boards at 433MHz 制造商:Semtech 功能描述:2 X SX1212SKA
SX1212-DK7A433
制造商:Semtech Corporation 功能描述:Evaluation Board for SX1212 Transceiver
SX1212IWLTRT
功能描述:IC TXRX 300MHZ-510MHZ 32-TQFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件
SX1213
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra-Low Power Integrated UHF Receiver
SX1213IWLTRT
制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:SX1213 Series 510 MHz 200 Kbps Ultra-Low Power Integrated UHF Receiver - TQFN-32
SX1223
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:425 - 475 MHz / 850 - 950 MHz Integrated UHF Transmitter